FAQs | Find Answers

Search Results

Results 21 - 30 of 319

Recommended Links
  1. How to Reset the Password for the TeraStation
    [Answer ID: 14931]
    TeraStation TS4000, TS5000, and TS7000 TeraStation TS-8VHL, TS-6VHL, TS-QVHL, TS-WVHL, TS-RVHL TeraStation TS-TGL / TS-HTGL / TS-RHTGL / TS-ITGL / TS-RITGL / TS-DHTGL / TS-X series...
  2. How to: Enable and Set Jumbo Frame (Ethernet frame) size for the TeraStation
    [Answer ID: 14685]
    Enabling jumbo frames support will greatly improve read/write operation to NAS device on the LAN network.However, jumbo frame setting may not be supported by some routers and host PCs. Internet access may  not be possible due to MTU setting variation and limitation of  intermediate routers....
  3. How To: Set up Web Server (php and MySQL) on the TeraStation
    [Answer ID: 14723]
    TeraStation can be setup as a web server to share web contents publicly or privately .The WEB hosting feature is implemented by a dedicated Apache web server, MySQL Data Base server and PHP support....
  4. Replacing a hard drive with higher capacity of drive in the TeraStation
    [Answer ID: 14105]
    It can be larger, but not smaller if it's part of a RAID 1 or RAID 5 array.The extra space in the case of a larger drive won't be added to the total volume of the TeraStation.If a smaller drive is used, TeraStation will reply with an error when an attempt to rebuild the RAID array....
  5. Conditions that cause the TeraStation to perform a RAID Check
    [Answer ID: 14111]
    The TeraStation will perform a Disk Check under a few conditions. If the TeraStation was shutdown improperly, it will perform a Disk Check the next time it boots.There are a number of ways the TeraStation can be shut down improperly:...
  6. Replaced drive on the TeraStation and still receiving a RAID error
    [Answer ID: 14116]
    After you replaced a drive, you need to restructure array onto the new drive.Check to make sure user restructured the RAID array onto the new drive.To do this: Go to Disk Management->RAID Configuration and click on RAID Array 1 (or RAID Array 2 if second Array failed in Mirrored Mode)....
  7. How to Set up a TeraStation Using Mac OS
    [Answer ID: 14162]
    To configure the NAS device from an Apple OS Boot the NAS device while it is connected to the router. Access the settings of the router and look at the DHCP client list.This will show the IP address the NAS device received or use NAS Navigator2, which will show the IP address, the hostname, the firmware version on more information about your Buffalo NAS device....
  8. Why does the transfer speed go down when replication is configured?
    [Answer ID: 14520]
    When the replication source data is updated, the data is transferred to the replication target.This data transfer causes a load increase to the TeraStation, which results in lower transfer speed....
  9. What action is to be taken in case of disk error?
    [Answer ID: 14566]
    Regular report in Email notification function: DISK error status[DISK error status] For example, "DISK3 1"means a read error was detected once in the Disk3.In case the error counter indicates a small number such as "1", an immediate disk replacement is not required....
  10. TeraStation - Replacement Hard Drive
    [Answer ID: 15005]
    Note:LinkStation Quad 6 TB & TeraStation ES, III and III iSCSI 6 TB models (specifically: LS-Q6.0TL/R5, TS-XE6.0TL/R5, TS-X6.0TL/R5, TS-RX6.0TL/R5 and TS-RIX6.0TL/R5) use 1.5 TB hard drives and should use OP-HD1.5T as the replacement drive.#30; For all other capacities and models, please refer to the chart above and then select the appropriate capacity....
< Previous  1  2  3  4  5  6  7  8  9  Next >

Refine your search

Select Product / OS & Hardware

      Enter Keywords or a specified ID